Technical Information › Marine Plywood
Marine plywood is a high grade hardwood plywood made to British Standard BS 1088. It is built from durable tropical hardwood veneers, bonded with a fully waterproof adhesive and made without core gaps, so it holds its strength in wet and humid conditions.
Key Specification
| Standard | BS 1088-1:2003 Marine plywood |
|---|---|
| Service class | EN 636-3 (exterior conditions) |
| Bond class | EN 314-2 Class 3, a weather and boil proof glue line, typically a phenolic resin |
| Timber | Selected tropical hardwoods, such as Okoume (Gaboon) from Africa or Far Eastern hardwoods such as Meranti |
| Face grade | B/BB. Clean face, minor colour variation, sanded both sides |
| Core | No core gaps, overlaps or voids permitted |
| Density | Approximately 490 to 600 kg/m³, depending on species |
| Moisture content | Between 6% and 14% when it leaves the mill |
| Formaldehyde class | E1 (low emission) |
| CE / UKCA attestation | System 2+ (shown as CE2+) |
| Sheet size | 2440 x 1220 mm (8 ft x 4 ft) |
| Thicknesses we supply | 6, 9, 12, 15, 18 and 25 mm |
| Sourcing | FSC or PEFC certified material, where stated on the product |
How BS 1088 Plywood Is Made
- Durable veneers: every ply is cut from timber rated durability class 3 or better, with only a small amount of sapwood allowed.
- Ply count: boards up to 6.5 mm have at least three plies. Thicker boards have five or more.
- Face veneers: each outer face is at least 1 mm thick after sanding on boards over 3.8 mm. Inner plies are no thicker than 4.8 mm.
- Balanced build: the outer plies make up 40% to 65% of the total thickness, which helps keep the board flat and stable.
- No defects inside: open joints, core gaps, overlaps, blisters and sanding through are not allowed.
- Bond testing: glue lines are tested to EN 314-1 and must reach Class 3 under EN 314-2.
Standard and Lightweight Panels
Standard (S)
Made from hardwoods with a nominal density above 500 kg/m³. The tougher, heavier option for structural and high wear use.
Lightweight (LW)
Made from lighter species such as Okoume (Gaboon). Easier to handle and bend, popular for boat building. All other BS 1088 rules still apply.
Approximate Sheet Weights (2440 x 1220 mm)
| Thickness | Approximate weight per sheet |
|---|---|
| 6 mm | 9 kg |
| 9 mm | 13 kg |
| 12 mm | 18 kg |
| 15 mm | 22 kg |
| 18 mm | 27 kg |
| 25 mm | 37 kg |
Based on 500 kg/m³. Heavier species and moisture content will increase these figures.
Panel Markings
Genuine BS 1088 sheets carry a permanent mark on the back face or edge showing:
- BS 1088-1:2003 and the word MARINE
- Nominal thickness
- Manufacturer name or mark, and country of manufacture
- Panel type, S (standard) or LW (lightweight), and timber species
- TREATED or UNBALANCED, if these apply
Typical Uses
- Boat building, pontoons, jetties and other waterside work
- Exterior joinery, signage, cladding panels and soffits
- Bathrooms, wet rooms and kitchens
- Horse boxes, van linings and trailer floors
- Garden buildings, decking areas and outdoor furniture
Storage, Handling and Finishing
Storage
- Store flat, indoors and off the ground on level bearers.
- Keep sheets covered and away from direct heat.
- Leave sheets in the room where they will be used for 48 hours before fitting.
Cutting and Fixing
- Cut with a fine toothed blade, face side up for hand saws and face side down for circular saws.
- Pre-drill near edges to avoid splitting.
- Use stainless steel or hot dip galvanised fixings outdoors.
Sealing
- Seal every edge and any cut face before exterior use.
- Pay extra attention to end grain, where water enters first.
Finishing
- Marine plywood is not treated against rot unless marked TREATED.
- For outdoor use, apply a paint, varnish or oil system and keep it maintained.
The information on this page is general guidance only. Always check the product label and the manufacturer's Declaration of Performance for the exact specification of the sheet you have received. For technical questions, email contact@plywoodetc.co.uk.