Technical Information › MDF
MDF (medium density fibreboard) is made from fine wood fibres bonded with resin and pressed into flat sheets. It has no grain, no knots and a smooth, even surface, which makes it easy to cut, shape and paint. We supply standard, moisture resistant and fire rated MDF.
Key Specification
| Standard | EN 622-5 (dry process fibreboard) |
|---|---|
| Density | Approximately 700 to 760 kg/m³ |
| Formaldehyde class | E1 (low emission) |
| Surface | Smooth, sanded both sides |
| Full sheet size | 2440 x 1220 mm (8 ft x 4 ft). Fire rated MDF is also available at 3050 x 1220 mm (10 ft x 4 ft) |
| Standard MDF thicknesses | 2, 3 (white faced), 4, 6, 9, 12, 15, 18, 22 and 25 mm |
| Moisture resistant thicknesses | 12, 18 and 25 mm |
| Also available | 6 mm oak veneered MDF and MDF window boards |
| Sourcing | FSC or PEFC certified material, where stated on the product |
Types of MDF
| Type | Grade | Where to use it |
|---|---|---|
| Standard | MDF | Dry interiors. Furniture, shelving, panelling and joinery |
| Moisture resistant | MDF.H | Kitchens, bathrooms and utility rooms. Usually dyed green so it is easy to spot |
| Fire rated | Euroclass B or C | Wall and ceiling linings in public buildings and escape routes. Usually dyed red |
Moisture resistant MDF handles humid rooms well, but it is not waterproof. It should not be used outdoors or where it will get wet. For fire ratings explained, see our Fire Rated Plywood technical information.
Approximate Sheet Weights (2440 x 1220 mm)
| Thickness | Approximate weight per sheet |
|---|---|
| 2 mm | 4 kg |
| 3 mm | 7 kg |
| 4 mm | 9 kg |
| 6 mm | 13 kg |
| 9 mm | 20 kg |
| 12 mm | 27 kg |
| 15 mm | 33 kg |
| 18 mm | 40 kg |
| 22 mm | 49 kg |
| 25 mm | 56 kg |
Based on 750 kg/m³. MDF is heavy. Thicker sheets are a two person lift.
Typical Uses
Good for
- Furniture, cabinets, wardrobes and shelving
- Skirting, architrave, window boards and panelling
- Painted joinery and shop fitting
- Speaker boxes, signs and craft work
- Kitchens and bathrooms (moisture resistant grade)
Not recommended for
- Outdoor use of any kind
- Structural floors or roofs
- Areas that will get wet
- Long unsupported shelves carrying heavy loads, as MDF can sag over time
Working with MDF
Dust safety
- MDF dust is very fine. Always wear a dust mask rated FFP2 or better, and eye protection.
- Use dust extraction on saws and sanders, and work in a well ventilated area.
Cutting
- Use a sharp, fine toothed blade for a clean edge.
- MDF can be routed and shaped well, which makes it ideal for mouldings.
Fixing
- Always drill a pilot hole. Screwing without one can split the board.
- Use screws made for MDF or chipboard, and keep them well away from the edges.
- Edges hold screws less well than faces.
Painting
- Seal cut edges first, as they soak up paint quickly.
- Prime with an MDF primer or a thinned coat of paint, sand lightly, then apply the top coats.
Storage and Handling
Storage
- Store flat on a level surface, indoors and dry.
- Do not stand sheets on edge for long periods, as they can bend.
Before fitting
- Leave sheets in the room for 48 hours before use.
- Protect corners and edges, which damage easily.
The information on this page is general guidance only. Always check the product label and the manufacturer's Declaration of Performance for the exact specification of the sheet you have received. For technical questions, email contact@plywoodetc.co.uk.