Skip to content

OSB Technical Information

OSB (oriented strand board) is an engineered board made from long strands of timber, laid in layers and bonded with a water resistant resin under heat and pressure. The strands in the outer layers run lengthways, which gives the board its strength along the length of the sheet. The OSB we supply is OSB/3, a load bearing board for use in humid conditions.

Key Specification

Standard EN 300, type OSB/3
Grade Load bearing board for use in humid conditions
Timber Softwood strands, usually pine or spruce
Density Approximately 600 to 650 kg/m³
Formaldehyde class E1 (low emission)
CE / UKCA attestation System 2+ for structural use
Square edge size 2440 x 1220 mm (8 ft x 4 ft)
Square edge thicknesses we supply 9, 11 and 18 mm
Tongue and groove 18 mm OSB/3 with a tongue and groove on all four edges (TG4), for flooring
Sourcing FSC or PEFC certified material, where stated on the product

Understanding OSB Grades

Grade Conditions Use
OSB/1 Dry General purpose and furniture, not load bearing
OSB/2 Dry Load bearing
OSB/3 Humid Load bearing. The most common grade in UK building
OSB/4 Humid Heavy duty load bearing

Humid conditions means protected from the weather, such as under a roof covering or behind cladding. OSB/3 is not designed to be left exposed to rain for long periods.

Typical Uses

Good for

  • Roof decking under felt, membrane or tiles
  • Wall sheathing on timber frame buildings
  • Floors and loft boarding (tongue and groove boards)
  • Site hoarding and temporary works
  • Sheds, garden buildings and workshop linings
  • Packing cases and pallets

Not recommended for

  • Long term exposure to rain without a protective covering
  • Permanently wet areas or ground contact
  • Fine furniture or work needing a smooth paint finish
  • For a smooth face, choose plywood or MDF

Approximate Sheet Weights

Board Approximate weight per sheet
9 mm, 2440 x 1220 mm 17 kg
11 mm, 2440 x 1220 mm 20 kg
18 mm, 2440 x 1220 mm 33 kg

Based on 620 kg/m³. Actual weight varies with moisture content.

Fitting Advice

Direction

  • Lay boards with the long edge across the joists or rafters, as the board is strongest along its length.
  • Stagger the end joints from row to row.

Expansion gaps

  • OSB grows slightly as it takes in moisture.
  • Leave a small gap between square edge boards and a wider gap around the edges of a floor or roof, as set out by the manufacturer.

Fixing

  • Fix with ring shank nails or screws, at the spacing given by the manufacturer.
  • Keep fixings at least 8 mm from the board edges.
  • Glue tongue and groove joints on floors with a suitable wood adhesive.

Spans

  • The thickness you need depends on the joist or rafter spacing and the load.
  • Always follow the manufacturer's span tables or your engineer's design for structural work.

Panel Markings

OSB sheets are printed with a stamp showing:

  • EN 300 and the grade, for example OSB/3
  • Nominal thickness
  • Manufacturer name and production batch
  • The CE or UKCA mark
  • Formaldehyde class, for example E1

Storage and Handling

Storage

  • Store flat, indoors and off the ground on level bearers.
  • Keep sheets dry. Edges swell if they get wet.
  • Leave sheets in the building for 24 to 48 hours before fitting.

On site

  • Cover the work as soon as possible after fitting.
  • Seal any cut edges that will be exposed to humid conditions.
The information on this page is general guidance only. Always check the product label and the manufacturer's Declaration of Performance for the exact specification of the sheet you have received. For technical questions, email contact@plywoodetc.co.uk.