Skip to content

Hardwood Plywood Technical Information

Technical Information › Hardwood Plywood

Hardwood plywood is a general purpose sheet made from thin layers of hardwood veneer, glued together with the grain of each layer running at right angles to the next. This cross-laminated build makes it strong, stable and easy to work. The hardwood plywood we supply is made to EN 636-2, for use in dry and humid conditions.

Key Specification

Standard EN 636-2 (plywood for humid conditions)
Structural marking EN 636-2S on most sheets 9 mm and thicker. Thinner sheets are generally for non-structural use
Bond class EN 314-2 Class 2 as a minimum. Many sheets use a Class 3 glue line
Timber Tropical hardwoods from Malaysia and Indonesia, or eucalyptus and poplar from China, depending on the mill
Face grade Typically BB/CC. Some sheets are B/BB with a cleaner face
Density Approximately 540 to 650 kg/m³, depending on species
Formaldehyde class E1 (low emission)
CE / UKCA attestation System 2+ (shown as CE2+) on structural grades
Full sheet size 2440 x 1220 mm (8 ft x 4 ft)
Thicknesses we supply 4, 6, 9, 12, 15, 18 and 25 mm
Cut sizes Smaller handy sizes are also available, from 305 x 305 mm upwards
Sourcing FSC or PEFC certified material, where stated on the product

Understanding EN 636 Classes

Class Conditions Where it can be used
EN 636-1 Dry Normal heated interiors only
EN 636-2 Humid Interiors with raised humidity, and protected exterior work kept out of direct rain
EN 636-3 Exterior Exposed to the weather or to long periods of high humidity

The letter after the class shows the intended use. S means structural (load bearing) and G means general purpose. A board can never have a higher EN 636 class than its glue bond class under EN 314-2.

Face Grades Explained

B Grade

A clean, fully sanded face with only minor colour variation. The best choice where the face will be painted or left on show.

BB Grade

A generally clean face with some neat patches or plugs where small knots or defects have been repaired and sanded.

CC Grade

A more open back face. Small splits, knots and colour changes are allowed. Normally used for the hidden side of the sheet.

How grades are written

The face grade comes first and the back grade second. BB/CC means a BB face and a CC back.

Hardwood Plywood or Marine Plywood?

Hardwood plywood Marine plywood
Standard EN 636-2 BS 1088 and EN 636-3
Conditions Dry and humid, protected exterior Wet, exposed and marine
Core Small core gaps may occur No core gaps allowed
Durability Varies by species Durable species only
Best for Furniture, joinery and general building work Boats, wet areas and exposed exterior work

For full details on marine grade sheets, see our Marine Plywood technical information.

Approximate Sheet Weights (2440 x 1220 mm)

Thickness Approximate weight per sheet
4 mm 7 kg
6 mm 11 kg
9 mm 16 kg
12 mm 21 kg
15 mm 27 kg
18 mm 32 kg
25 mm 45 kg

Based on 600 kg/m³. Actual weight varies with species and moisture content.

Panel Markings

Sheets made to EN 636 are marked on the back face or edge. Look for:

  • EN 636 followed by the class, for example EN 636-2S
  • Nominal thickness
  • Manufacturer name or mark
  • CE or UKCA mark and the Declaration of Performance reference on structural grades
  • Formaldehyde class, for example E1

Typical Uses

Good for

  • Furniture, shelving and cabinet carcasses
  • Internal joinery, wall linings and partitions
  • Kitchens, utility rooms and other humid rooms
  • Van linings, workbenches and shop fitting
  • Packing cases, hoarding and general building work
  • Protected exterior work such as soffits under a roof overhang

Not recommended for

  • Fully exposed exterior work left open to the rain
  • Permanently wet areas, ground contact or immersion in water
  • Boat building
  • For these, choose marine plywood or a board marked EN 636-3

Storage, Handling and Finishing

Storage

  • Store flat, indoors and off the ground on level bearers.
  • Keep sheets dry and covered.
  • Leave sheets in the room where they will be used for 48 hours before fitting.

Cutting and Fixing

  • Use a sharp, fine toothed blade to limit splintering of the face veneer.
  • Score the cut line with a knife for a cleaner edge on show faces.
  • Pre-drill close to edges to avoid splitting.

Sealing

  • Seal all edges and cut faces in humid areas or protected exterior work.
  • Edges take in moisture faster than the faces.

Finishing

  • Lightly sand before painting, staining or varnishing.
  • Hardwood plywood is not treated against rot. Protect it with a suitable finish and keep it maintained.
The information on this page is general guidance only. Always check the product label and the manufacturer's Declaration of Performance for the exact specification of the sheet you have received. For technical questions, email contact@plywoodetc.co.uk.